XT610 Europe stuck in Bootloader 3.01c after flashing SBF

[superilse]

Hello everybody.

Today changed from Galaxy S to Motorola Pro XT610.

I tried to upgrade with RSD Lite and the DROIDPRO_2.26.20_FULL.sbf file.

But in the end of flashing there is a message that its failed.

After flashing the XT610 is stucked in Boot Mode with the message:

Bootloader 03.0c

Code corrupt

Then i can flash again, if i want, but after flashing the same Message.

r+m+on is not helping.

x+on is not helping too.

The Verizon Blur Release is not helping too.

Has anyone an idea?

The Flash Log shows the following entries after flashing:

16:28:44, September 03, 2011
Line: 537
ERROR: AP Die ID: 07000205259f3a0a0000d8ff0100

16:28:44, September 03, 2011
Line: 544
ERROR: BP Die ID: 000000000000000075603289fc84

16:28:44, September 03, 2011
Line: 551
ERROR: AP Public ID: bfafc4280db4b18936cf671182cb6f9b49459c09

16:28:44, September 03, 2011
Line: 558
ERROR: BP Public ID: 040000000500000002000000ffff000051083289

16:34:26, September 03, 2011
Line: 608
ERROR: Interface BP: Error sending JUMP command Device API Error: 0xE003003F Address: 0x800000 Command: JUMP
File: D:\GitProjectsReleases\hdt_windows_flash\flash\cod e\flashdll\RDLOp.cpp
Device ID: 0

16:34:26, September 03, 2011
Line: 328
ERROR: Interface BP: Error jumping to RAM Downloader
File: D:\GitProjectsReleases\hdt_windows_flash\flash\cod e\flashdll\RDLOp.cpp
Device ID: 0

16:34:26, September 03, 2011
Line: 1195
ERROR: Phone[0000]: Flash failed.
File: D:\GitProjectsReleases\hdt_windows_flash\flash\cod e\flashdll\PST_FP_FlashThread.cpp
Device ID: 0

16:34:26, September 03, 2011
Line: 610
ERROR: Flash failure: Interface BP: Error sending JUMP command Device API Error: 0xE003003F Address: 0x800000 Command: JUMP (Error Code: e003003f),
Detailed Error Details: Direction of the Error=2000, Command Value=500000, Code Group Number=No Codegroup
File: D:\GitProjectsReleases\hdt_windows_flash\flash\cod e\flashdll\FlashHdlr.cpp
Device ID: 0

16:34:46, September 03, 2011
Line: 1507
ERROR: Error getting subscriber unit information.
File: D:\GitProjectsReleases\hdt_windows_flash\flash\cod e\flashdll\PST_FP_FlashThread.cpp




... while finding a solution now ive low battery and I cannot flash.

So I just did a "special USB Cable"
according to normal USB specification

and now battery is loading. I hope so.

In an hour I will retry the flash on another notebook with new installed drivers.

Hope that this will solve my problem



Battery is full now. But flashing is ending with error.

Ive installed new drivers 5.2

I dont know what happened to my Motorola Pro. Its a European Version, not Verizon.

Is it bricked? So I have to send it to the service?

Or it is the wrong SBF file?

Anyone knows if there is a SBF file for european Motorola Pro? Maybe i used the wrong one?

Is there any way to get back?

The phone was original in the beginning, no root, no nothing.

I just tried to flash the SBC.

---

View attachment 39869

 

[bsweetness]

That SBF is only for the Verizon Droid Pro from the US. The Motorola Pro released in Europe, while nearly identical, actually has some hardware and software differences. It's not the same phone as the Verizon Droid Pro. SBFs are phone specific, meaning they can only be used with the phone they were made for. You can't flash the SBF intended for one phone onto another, even if the phones seem like they're the same.

The only way that I know to fix it would be to flash a SBF for the Europen Motorola Pro, but I've never seen one posted online. Hopefully someone else might know where to find one or can suggest another route to help you out. But when flashing a SBF, always make sure it's for your exact phone, or else you'll cause major problems (like you're having).