Shell/Holster Combo problem.

Discussion in 'Android Accessories' started by nubirai, Nov 23, 2009.

  1. charrry

    charrry Member

    Joined:
    Nov 8, 2009
    Messages:
    38
    Likes Received:
    0
    Trophy Points:
    6
    Location:
    Los Angeles
    Ratings:
    +0
    I have the car dock...no use getting case, will have to keep taking it off
     
  2. will.anaya

    will.anaya Member

    Joined:
    Nov 11, 2009
    Messages:
    113
    Likes Received:
    0
    Trophy Points:
    16
    Location:
    San Antonio
    Ratings:
    +0
    i too have the car dock and the back part of the case is real easy to remove.

    just have to make sure you store it some where safe so as not to crush the case.
     
  3. SG181

    SG181 Member

    Joined:
    Dec 9, 2009
    Messages:
    44
    Likes Received:
    0
    Trophy Points:
    6
    Ratings:
    +0
    I'm fairly happy with the shell/holster combo on my Droid, however it seems like the back section of the case is bent, particularly when I look at it from the left (USB) side. It almost seems like the USB cutout it just a little too small. Has anyone else noticed this on their shell?
     
  4. BCrawford

    BCrawford Member

    Joined:
    Nov 19, 2009
    Messages:
    110
    Likes Received:
    1
    Trophy Points:
    18
    Location:
    Southeast PA
    Ratings:
    +1
    I noticed this too. It drove me nuts. I like this case, but between that and the upper right hand clip that I had to dremel off I feel like I made this case. I took a piece of paper 3 inches wide by 1.5 inches tall. I folded it in half width-wise three times. Put it in between the case and the phone starting at the top of the USB port and going towards the speaker with it. It looks much better and stays in the holster much more securely.
     
  5. TheOldFart

    TheOldFart Active Member

    Joined:
    Nov 26, 2009
    Messages:
    963
    Likes Received:
    27
    Trophy Points:
    28
    Location:
    New York State
    Ratings:
    +27
    I filed the tab off mine too. I tried your paper trick and it worked good to make the USB edge straighter. However, it still looked better then the Seidio case shown in the photos in post 384 in this thread:

    http://www.droidforums.net/forum/droid-accessories/4859-seidio-case-39.html
     
  6. baniels

    baniels Member

    Joined:
    Dec 19, 2009
    Messages:
    574
    Likes Received:
    0
    Trophy Points:
    16
    Location:
    52556
    Ratings:
    +0
    Samed here. Tried three at VZ store yesterday. They all have that same problem corner. Pretty disappointing. I filed off that tab, but I'm still probably going to return it.
     
  7. baniels

    baniels Member

    Joined:
    Dec 19, 2009
    Messages:
    574
    Likes Received:
    0
    Trophy Points:
    16
    Location:
    52556
    Ratings:
    +0
    Fyi, I received the one I had ordered last week from the website, and it does not have the same problem. Fits at all corners and is straight all around. They may have adjusted their tolerances.
     
Search tags for this page
droid 2 global case holster combo
,

droid 2 global shell holster combo

,
droid 2 shell holster combo
,
holster combo
,
motorola droid 2 shell holster combo