{Source Edit Build} GimpSource 3.1 | FRG83D | Source Build ROM |

[sparty569]

Downloaded and installed. Restoring apps, went through the GimpSource settings and got just about everything tweaked. Will apply Slayhers 1.25 kernel and Gimpybread and I will be all set.

Looking good so far. All that is needed is the MIUI/CM7 sliders for phone and text on the lockscreen.

[azpilot]

Report -
Nice and fast -

Issue when you enable the Galaxy S bar and then reboot, the bar does not show back up and you have to go and re-enable it.

Once its enabled however -
Click on wifi and then turn off its pretty hard, does not update correctly, have to toggle out of the notification screen and back to toggle it.
Click on Bluetooth, locks up solid and then phone reboots
Colors do not change if you change them, still shows green for selected widget

If Bluetooth is enabled and you reboot, the phone locks up and just resets.

[guidot]

Report -
Nice and fast -

Issue when you enable the Galaxy S bar and then reboot, the bar does not show back up and you have to go and re-enable it.

Once its enabled however -
Click on wifi and then turn off its pretty hard, does not update correctly, have to toggle out of the notification screen and back to toggle it.
Click on Bluetooth, locks up solid and then phone reboots
Colors do not change if you change them, still shows green for selected widget

This is an issue with kernel.

Change to any kernel you know works with the phone.

[azpilot]

Report -
Nice and fast -

Issue when you enable the Galaxy S bar and then reboot, the bar does not show back up and you have to go and re-enable it.

Once its enabled however -
Click on wifi and then turn off its pretty hard, does not update correctly, have to toggle out of the notification screen and back to toggle it.
Click on Bluetooth, locks up solid and then phone reboots
Colors do not change if you change them, still shows green for selected widget

This is an issue with kernel.

Change to any kernel you know works with the phone.

I would think this is a deal breaker then and would not supply that kernel. Here is why I say this, sure I cruised past the first page, DL and install, go through my routine, I would rather flash the kernel of my choice to start with or not at all (Normally I don't), then get stuck in a permanent boot loop and have to re-flash again. IMO its a waste of time for me, you (cause you have tell me its the kernel) and others that might run into this. If I'm going to flash a kernel in the first place (or last) then that should be my choice.

[azpilot]

Kernel fixed the FC and bootloops, however enable the Galaxy S widget still not working correctly. Once its enabled, then enable the rotary lockscreen and reboot, the Galaxy widget then is gone. Enable again and change colors to other than the green and it does not take effect.

[swallisa]

Kernel fixed the FC and bootloops, however enable the Galaxy S widget still not working correctly. Once its enabled, then enable the rotary lockscreen and reboot, the Galaxy widget then is gone. Enable again and change colors to other than the green and it does not take effect.

AZ try enable galaxy widget and not rebooting should come up fine. Then reboot after should come back. Mine has come back after multiple reboots.

[azpilot]

I tried a couple of things, however now I'm FC and Stuck right at bootup after installing ADW. I think I'll go back to 2.0, I had no trouble with that, and this is just too much to want to deal with right now.

[swallisa]

I tried a couple of things, however now I'm FC and Stuck right at bootup after installing ADW. I think I'll go back to 2.0, I had no trouble with that, and this is just too much to want to deal with right now.

Did you try a fresh download as I am not seeing any of the things your talking about?

[azpilot]

I tried a couple of things, however now I'm FC and Stuck right at bootup after installing ADW. I think I'll go back to 2.0, I had no trouble with that, and this is just too much to want to deal with right now.

Did you try a fresh download as I am not seeing any of the things your talking about?

Yep fresh download, fresh load, wipe everything.. I pretty much do the same routine with loading Roms and this is the first one to give me fits. Its all good I'll mess with it some other time..I guess I"m Rom'd out right now.. LOL

[swallisa]

I tried a couple of things, however now I'm FC and Stuck right at bootup after installing ADW. I think I'll go back to 2.0, I had no trouble with that, and this is just too much to want to deal with right now.

Did you try a fresh download as I am not seeing any of the things your talking about?

Yep fresh download, fresh load, wipe everything.. I pretty much do the same routine with loading Roms and this is the first one to give me fits. Its all good I'll mess with it some other time..I guess I"m Rom'd out right now.. LOL

I hear ya sometimes it gets like that what was your replacement kernel just curious?