DroidForums.net is the original Verizon Android Forum! Registered Users do not see these ads. Please Register - It's Free!
Results 1 to 9 of 9

Thread: D2G Sfb flash failed?

  1. Junior Droid
    NickHutch's Avatar
    Member #
    160625
    Join Date
    Jan 2011
    Posts
    7
    Phone
    Droid 2 Global
    #1

    D2G Sfb flash failed?

    I tried to flash my D2G just to get everything back to out of the box, using the posted SFB, and I downloaded RSDlite 4.9 and I have the drivers.

    After I try to flash it states "Failed flashing process. Failed flashing process. Phone[0000]: Error switching phone to BP pass through mode (0x70BE0); phone disconnected.

    I don't know what else to do, any help?
  2.  
     
     
     
  3. Junior Droid
    tmhung's Avatar
    Member #
    99625
    Join Date
    Aug 2010
    Posts
    21
    Twitter
    tmhung
    Phone
    Droid Razr XT912
    #2
    Quote Originally Posted by NickHutch View Post
    I tried to flash my D2G just to get everything back to out of the box, using the posted SFB, and I downloaded RSDlite 4.9 and I have the drivers.

    After I try to flash it states "Failed flashing process. Failed flashing process. Phone[0000]: Error switching phone to BP pass through mode (0x70BE0); phone disconnected.

    I don't know what else to do, any help?
    I think you need installing 64bits driver in RSDlite pack
  4. Junior Droid
    NickHutch's Avatar
    Member #
    160625
    Join Date
    Jan 2011
    Posts
    7
    Phone
    Droid 2 Global
    #3
    Installing 64-bits driver? Where would I get that at? I'm downloading the moto drivers back off of there website. Is that the driver that I need?
  5. Junior Droid
    NickHutch's Avatar
    Member #
    160625
    Join Date
    Jan 2011
    Posts
    7
    Phone
    Droid 2 Global
    #4
    Now my phone won't even show up in RSDlite to try and flash it anymore. I guess its completely screwed...
  6. Senior Droid
    tebower's Avatar
    Member #
    12892
    Join Date
    Dec 2009
    Posts
    160
    Liked
    1 times
    Phone
    Droid 2 Global
    #5
    I doubt you're screwed. You have the cable, the SBF, the phone, and the software. There is probably something small that you're missing. I'd take a break, and start over in a bit.

    Follow the steps for Method 2 on this site:
    Droid 2 Global SBF File (2.4.29) Full and RSDLite

    Have the driver files extracted to an easily located file (like on the desktop) so that you can find them if prompted. Make sure you also have the baseband drivers. If you don't, search for them or PM me, I can email you a ZIP.

    Don't touch your phone during the process. The error you mentioned made it sound like your cable had lost it's connection (the 'phone disconnected' part).

    Persistence and research...you'll get it working.
    Last edited by tebower; 01-14-2011 at 09:30 AM.
  7. Junior Droid
    NickHutch's Avatar
    Member #
    160625
    Join Date
    Jan 2011
    Posts
    7
    Phone
    Droid 2 Global
    #6
    No idea how, or why. I was already using method 2. I just tried it again and it worked. I'm so happy right now lol.
  8. Beta Team
    buryboi's Avatar
    Member #
    17603
    Join Date
    Dec 2009
    Posts
    234
    Liked
    3 times
    Phone
    Droid
    DroidForums.net Developer
    Premium Member
    #7
    Nick,
    I just had a similar experience...

    I'd get all the way through each block of the sbf, and then it would try to put the phone into BP pass though mode, stall for a bit and Fail. When the phone switched to BP pass through notification popped up like windows recognized a new device, but it never asked for drivers, and acted like it was installed fine.

    After failing twice, my battery died (and then you cant do anything till it gets charged). This all took place under windows 7 64.

    Lucky for me, I know someone with a D1 and borrowed the battery and started over.

    With a fresh battery I tried it all again on a winxp (not 64) pc. Installed the latest moto drivers from their site. Found Here:

    Moto Drivers 4.8.0

    Installed Rsd lite 4.9 and plugged in my phone (it was already in bootloader mode, since it had failed twice before.

    This time, it went through the flash, switched to BP pass through mode and finished fine (I did have to boot into recovery and factory reset to get past bootloop).

    When it got to BP Pass Through mode, windows recognized the phone as MDM6600 device and automatically installed the drivers. This is where it hung on the windows 7 machine, and I'm pretty sure it's because it didn't automatically install the drivers. The full sbf RSD lite package includes those drivers (the tbf release package). If you cant try it on a windows xp machine, you'll have to act quick and be ready for the phone to switch to BP pass through mode.

    If you cant try from an XP machine try this:

    Get ahold of the MDM6600 64 bit drivers (either from tebower or elsewhere), unzip them to a location you can easily find, and open Device manager.

    Start the sbf as normal. When it tries to switch your phone to BP pass through mode quickly go into device manager, find the motorola device, right click it and select update drivers.

    Tell it not to search but that you have the files on the pc. Browse to wherever you stored the MDM6600 64 bit drivers and install those.

    If it gets the drivers installed quick enough, rsd lite should successfully recognize the phone in BP pass through mode and continue onward.

    Good luck.
  9. Junior Droid
    NickHutch's Avatar
    Member #
    160625
    Join Date
    Jan 2011
    Posts
    7
    Phone
    Droid 2 Global
    #8
    It already worked for me, it must have found the drivers on its own, or when I downloaded motohelper earlier, it must have installed the ones i needed. Thanks for the help though.
  10. Master Droid
    leobg's Avatar
    Member #
    75942
    Join Date
    Jun 2010
    Posts
    658
    Liked
    8 times
    Phone
    Droid2 Global/XT860 4G(D3)
    #9
    When you install the drivers, windows does not prompt for restart, but in order device to be recognize you must restart Windows. I had same issue long time ago when I started flashing my Milestone. Once you install all drivers and programs, reboot and then use RSDlite - you will be fine.

Links

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Similar Threads

  1. GPS Failed? This May Fix It
    By Erich_F in forum Android Tech Support
    Replies: 12
    Last Post: 08-31-2011, 07:10 PM
  2. Sbf failed what do I do :(
    By ath2424 in forum Motorola Droid 2 Development
    Replies: 4
    Last Post: 01-10-2011, 08:15 PM
  3. flash failed?
    By gamble_it in forum Droid 2 Roms
    Replies: 4
    Last Post: 01-07-2011, 08:37 PM
  4. Failed Ultimate Droid flash
    By GTRHitman in forum Rescue Squad Help
    Replies: 10
    Last Post: 12-16-2010, 08:39 PM
  5. adobe flash or flash apps to view internet pages?
    By rabyfox in forum Android Tech Support
    Replies: 4
    Last Post: 02-24-2010, 11:34 AM

Search tags for this page

d2g bp
,
d2g driver
,

d2g drivers

,
droid 2 global error switching phone to bp pass through mode
,
droid 2 global failed flashing process
,
failed flashing process phone 0000 error switching phone to
,

flash mdm6600

,

flash mdm6600 driver

,
flash mdm6600 driver download
,
mdm6600 drivers x64 download signed
Click on a term to search our site for related topics.
Find us on Google+