Testers Needed for new kernel version v3227 (MIUI Compatible)

[jdlfg]

Im looking for a couple testers to run this new kernel version and report any bugs.z

Standard voltage ( please read this thread Low voltage causes high Android System?) very informative thread.
Scaling on demand by default
Posting this one v3227 850 MHz standard voltage.

http://dl.dropbox.com/u/6011176/v322...un-08_36AM.zip
http://dl.dropbox.com/u/6011176/v322...un-02_37PM.zip 1125 MHz tester

http://dl.dropbox.com/u/6011176/v322...hu-12_19PM.zip 900 MHz Tester

http://dl.dropbox.com/u/6011176/v322...hu-05_29PM.zip 1100 MHz Tester


More to come this is just a test run. I will also be working on kernels compatible with cm 7 rc's.

Installation: Place on root of sd
Boot into recovery or from rom manager install rom from sdcard.
Install zip from sdcard
Choose zip from sdcard
select zip.
Done.

[TMYINC]

I have ran your kernels a lot so I would be willing to give this one a try. I am actually on MIUI 1.1.7.0 right now so it would be a good time to try it out!

[boostedhonda]

Gonna try this out in about 10 minutes. Ill report results at the end of the day.

Sent From My Gingerbread Droid 1

[boostedhonda]

Well results weren't too good for me. On froyo and gingerbread it locks the phone up as soon as the phones finished booting up. Kinda weird because I've never had a problem with my phone using a kernel. I'm thinking since its after its done booting its like setcpu is locking it up as soon as it gains su permission. Ill try again in a lil bit without setcpu on.

Sent From My Gingerbread Droid 1

[jdlfg]

Well results weren't too good for me. On froyo and gingerbread it locks the phone up as soon as the phones finished booting up. Kinda weird because I've never had a problem with my phone using a kernel. I'm thinking since its after its done booting its like setcpu is locking it up as soon as it gains su permission. Ill try again in a lil bit without setcpu on.

Sent From My Gingerbread Droid 1

Which build?
Setcpu to. Ondemand@boot

[TMYINC]

Well results weren't too good for me. On froyo and gingerbread it locks the phone up as soon as the phones finished booting up. Kinda weird because I've never had a problem with my phone using a kernel. I'm thinking since its after its done booting its like setcpu is locking it up as soon as it gains su permission. Ill try again in a lil bit without setcpu on.

Sent From My Gingerbread Droid 1

I would say make sure all of your presets from the previous kernel are off before flashing. Anything that has "Set on boot" checked might cause it to bootloop. Not sure if that is the problem, just a thought I had.

[TMYINC]

So far everything is going well on MIUI v1.1.7.0. Have it set to On demand, sampling rate at 30000 and up threshold set to 51%. Screen off is set to min 300 and max 450 as well as the charging profile. So far no hiccups and no heat issues. I will continue to run it the rest of the day to observe battery life and such. Im looking forward to the rest of these kernels. Hopefully they will be updated on Rom Manager also. Thanks jdlfg for such awesome kernels.

[SSHGuru]

jd,

Are you running a MIUI ROM over a Lithmod rom? If so why? Should we try it out?

[TMYINC]

jd,

Are you running a MIUI ROM over a Lithmod rom? If so why? Should we try it out?

I was just thinking that he posted here since he supports LithiumMod and his kernels are usually what comes with Lithium Roms by default.

[jdlfg]

jd,

Are you running a MIUI ROM over a Lithmod rom? If so why? Should we try it out?

I have my Droid 1 laying around. It is not my everyday phone. However, I am not running MIUI but made these kernels compatible for the MIUI build at the request of a few friends. My D1 has lithmod installed. These kernels are built with standard voltages across the board. I am sure that they will show significant results in battery life and performance once released officially.