New Kernels for Koush ROM - multiples

[JonKyu]

@Jon - I ran this same update and my wifi is working correctly, can you tell me what is happening. Thanks.

Yeah I don't know what happened I tried installing this over a nandroid backup I had done using SPRecovery (did a wipe/restore and restored only the boot and system partition) and while it did boot up wifi wouldn't connect to my router. So I thought what the heck and reflashed it using ROM Manager and installed it as a update.zip and now everything is working again! Not sure what happened but it works after installing fresh.

[gotta have that funk]

ok, nevermind about the standby issue, this kernel doesnt allow tempmonitor cpu readings so back to the stock one i go..

it says it supports it on that mydroid site, but it doesnt work when i open temp monitor..hmm?

[Fronc]

Anybody experience soft reboots with 1100/1200? I was having this problem with other ROM's/Kernels, but since shifting to CM 5.0.4.2, I haven't had one, and thats @1000mhz.

I've been trying to figure out what the actual cause of the random soft reboots is, and the only thing I can imagine is that it is purely JIT-related.

If anyone has had any reboots I would like to know, so that I can isolate the problem, and won't bother trying 1100/1200.

Thanks!

[Flomaster]

Anybody experience soft reboots with 1100/1200? I was having this problem with other ROM's/Kernels, but since shifting to CM 5.0.4.2, I haven't had one, and thats @1000mhz.

I've been trying to figure out what the actual cause of the random soft reboots is, and the only thing I can imagine is that it is purely JIT-related.

If anyone has had any reboots I would like to know, so that I can isolate the problem, and won't bother trying 1100/1200.

Thanks!

Running the 1200 and have had no reboots at all. I just enabled JIT about 10 minutes ago so I'll see if I get any there if so I will disable JIT.

different phones like different kernels it might work for me and might not for you.

-=Jason=-

[Fronc]

Running the 1200 and have had no reboots at all. I just enabled JIT about 10 minutes ago so I'll see if I get any there if so I will disable JIT.

different phones like different kernels it might work for me and might not for you.

-=Jason=-

The unfortunate thing is that no matter what I try, it's going to be a whole new ballgame when I get my replacement droid on Weds/Thurs. (headphone jack is crackly at the slightest touch, and I assume its hardware)

Thanks, and I look forward to hearing your results.

[mrdroid]

Is the voltage jacked up on these kernals? Or is it standard voltage?

[srtfool32]

i cant get either to work for me. boots up on 1.2ghz and unlocked and moved screens and reboot, then reboots again before i can unlock the screen and rebooted again and finally froze at the middle of the bootanimation.

tried 1.1ghz and didnt even get to the unlock screen.

tried bekit 1ghz kernel and nada, had to restore my nandroid in cwm recovery to boot back up. any idea what happened? always run 1.2 ghz on UD 7.8 and all Ud roms.

[smacinskyjr]

why is it on chevys rom I can run his 1.2 ghz but with this kernal 1.2 only boot loops?

[Fronc]

1. Does the P3Droid-Koush-120 kernel work on CM 5.0.5?

2. Would I even want to do that, since the new CM uses a lowered-voltage kernel @1ghz?

Thanks!

[mrdroid]

why is it on chevys rom I can run his 1.2 ghz but with this kernal 1.2 only boot loops?

That leads back to my original question.. what is the voltage set to on this kernal? It's probably either too low or too high potentially causing physical damage.